LEXMARK OPTRA S 1255 DRIVER FOR MAC

Open the printer rear door to access the jam. Paper is either not leaving the duplex entry sensor in time or not making or unmaking the duplex exit sensor in time. The output bin sensor has not been unmade. Check the toner metering cam on back of suspect cartridge. Thank you and your firm again, you were terrific. Check the continuity of the fuser lamp at the two heavy leads. Error Engine Flash.

Uploader: Mikajora
Date Added: 5 November 2015
File Size: 69.45 Mb
Operating Systems: Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X
Downloads: 58934
Price: Free* [*Free Regsitration Required]

If the paper is jammed in the rear of the duplex, replace the duplex front cover and open the duplex rear door. Error code 31 is displayed when the top lexmark optra s 1255 lexmarm is closed and a defective print cartridge is detected. Jam at the duplex unit. Also, can I get some instructions on putting in the rollers. If the paper is not jammed in the duplex unit, then it may be jammed oltra the rear of the printer.

Reload the paper and do a power on reset. The output bin sensor has not been lexmark optra s 1255.

System Board Pricing Request Quote. Replace the assys in the following order 1. The exit sensor was not made in time after the input sensor as ootra. Erase lamp assembly missing or disconnected. Font card format not supported by printer. Make sure the memory shown on the printout matches the installed memory.

Lexmark optra s 1255 the bump alignment motor.

Check the toner metering cam on back of suspect cartridge. It can also be the LVPS low voltage power supply or a fuse in the power supply on some models. It may take lexmark optra s 1255 printer seconds to determine if lexmark optra s 1255 print cartridge is defective.

Serial Error – Framing or parity oprta on serial. Page too complex to print. This error indicates the printer was able to read the cartridge ID, but the ID did not pass the verification test. Mirror motor unable to reach operational speed, various other component level failures indicated by Software Error Unrecoverable software error.

Check developer drive for worn, loose or broken parts.

Check fan for binding or defective bearing – Replace Fan How did we do? Check the transfer roller for toner buildup, surface damage to the roller, oil, or other contaminants on the surface of the roller.

Duplex Not Attached Duplex is x connected but no longer mechanically attached, and printer top cover is closed. Replacement of the thermistor is not a cost effective repair, replace fuser assembly.

Make sure there is no paper jammed in the printer.

Remove toner cartridge for better access to jammed paper. No inkjet error codes available. Replace System Board Request Quote. Check AC power source for noise. Lexmark Fusers How did we do? Replace with the correct printhead. Any help here would lexmark optra s 1255 appreciated too. Printhhead Error – Lost Lock condition Lexmaek a problem with the mirror motor circuit in the printhead assembly or the mirror motor cable to the system board cable or system board assembly.

Fuser Error – Problem in the fuser, not heating, heating to quickly or too hot. Lexnark Pricing How did we do? In general, fuser errors require replacement of the fuser as a cost lexmark optra s 1255 repair.

Roller is approximately 2″ in circumference print defects with this repetitive spacing can be caused by transfer roller problems, on a standard 11″ page defect would repeat five times.

The lexmark optra s 1255 roller is included in the maintenance kit. Make sure there is continuity between the transfer roller and its contact on the HVPS; replace the transfer roll if the continuity is correct. Wayne Haub Kansas City. Defective font card installed in font slot. May be due to the paper feeding manually while motors running and previous page in path.

404 Not Found

Run the Quick Disk Test. Disk Full Not enough disk space for data that has been requested to be written to disk.

If the test fails, the disk lexmark optra s 1255 defective or the data on track1 is bad. Input sensor not made after optraa attempt. Replace the transfer roller as necessary. Check the left and right transfer roll arm assembly to make sure it is fastened and ooptra in the down position if applicable to your machine. If the error appeared while sending a job from the host to the printer, turn the printer off, then turn it on and try again.

The engine protocol violation detected by lexmark optra s 1255 specified device.

Lexmark Printer Error Code Information

Replace the Engine Lexmaark Request Quote. A error caused by low line voltage can sometimes be cleared by turning the machine off and then on again. Pay close attention to the area where the toner cartridge sits.