ELTRON CARD PRINTER P310I DRIVERS FOR WINDOWS

Spaces are the same width as the narrow bars. Command – Clear Error Status. Slot Card Cleaning Cartridge in final position Step 6. Appendix D This Appendix includes an example of a P com- mand sequence that offers both optimization and loopback features for duplex printing. If issued at Power-On, this command assures a clear media path for subsequent operations. The card printer can op- erate with both interfaces attached and communi- cating with the printer. Note that this command requires the prior installa- tion of a 5-panel ribbon and works best with mil cards.

Uploader: Nizil
Date Added: 22 March 2007
File Size: 38.93 Mb
Operating Systems: Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X
Downloads: 47388
Price: Free* [*Free Regsitration Required]

Enter text from picture: Page 19 Step 5. On second side, print last K panel then laminate: Appendix E This Elhron offers examples of Max Secure com- mand sequences for the various ribbon types.

This applies to the Pi only. IV Command – Print Clear Veneer Description This command serves either to print the entire ad- dressable image csrd or to reverse print with the clear veneer or any image data line, rectangles, graphics, text, etc.

Figure shows the same bit-map in association with compressed data Figure Non-Compressed Bit-Map x axis Rev. Spaces are the same eltron card printer p310i as the narrow bars.

Discard both cleaning cards after a single use. Eltron card printer p310i avoid contamination, always hold the frame and the roller by the ends. PDC Healthcare understands that excellent performing labels are important to your daily operation.

Healthcare Labels & Timemed Labeling Systems – PDC Healthcare

A command error condition eltron card printer p310i when image data extends beyond the addressable range of the image buffer. The programming commands control the printing process by color and by ribbon material, allowing overprinting and separate control of various multi- ple-overlay finishes.

The result- ing line overwrites any existing graphics data. Printers have the equivalent of an Extended Mem- ory.

X Command – Check Command Initiator! Troubleshooting Troubleshooting The table on the next page offers causes and solutions to symptoms related to improper operation. The following describes eltron card printer p310i typical Max Secure System operation: Table of Contents Add to my manuals Add.

Page 28 Cartridge will be installed initially, this area was covered by a warning tape. Card Prniter Cartridge in final position Close the printer main cover.

Zebra P330i User Manual

Zebra Technologies Corporation and may not be duplicated in full or in eltrln by any person without written approval from Zebra. The equation to calculate the Code B bar-code length is: By Site Ambulatory Surgery Centers.

Table of Contents Add to my manuals Add. Also note that these 3 characters are automatically managed by the magnetic encoder according to the ISO Standard Norms. Rotational parameters clockwise exist for the fol- lowing: Sent to Module 2 of P and P This suits the front-to-back loading of Print Head Registers and the right-to-left card movement dur- ing print cycles.

Launch Microsoft Word Software. Copyright Notice Zebra Eltron card printer p310i Corporation and may not be duplicated in full or in part by any person without written prniter from Zebra. Troubleshooting The table on the next page offers causes and solutions to symptoms related to improper operation. Locate the eltron card printer p310i at the rear of the Card Cleaning Cartridge mounting location; see below.

Page 27 ribbons have resin black followed by varnish pan- els, both limited to monochrome data.

PDC Healthcare Products: Medical Labels & ID Solutions

The card printer can op- erate with both interfaces attached and communi- priinter with the printer. Charting Supplies See All. Appendix C This section contains eltron card printer p310i on the magnetic stripe card encoder operation and formatting for all models except the Max Secure Series. I Command – Print Monochrome Graphics I Command – Print Monochrome Graphics Description This command serves to print a monochrome graphic panel from a card image previously stored in the buffer designated for Resin images.